Place an old towel in the bottom of the tub to prevent the porcelain or fiberglass surface from being scratched while you work. The adapter kit comes with a diverter device that attaches to the shower stem and can direct the water in either of two directions (pictured). This enables you to use two showerheads from a single water source. Remove the old showerhead using adjustable pliers. You may want to wrap the jaws of the pliers with tape to prevent them from marring the chrome. Using a rag (and, if necessary, some paint thinner) to remove any old plumber's putty or Teflon tape left on the threads of the shower stem. With the old showerhead removed, you can attach the diverter. It's important to make sure that the supplied washer is placed in the neck of the diverter according to the directions that come with the kit (pictured). Apply some new Teflon tape to the threads of the shower stem to help prevent water leakage (pictured). When applying Teflon tape, wrap it in the direction that the fixture will be tightened.

If the tape is wrapped in the opposite direction, it may tear when the fixture is installed on the threads, and thus will be ineffective at preventing leaks. With the Teflon tape applied, attach the diverter to the shower stem (pictured), and hand-tighten it. Carefully tighten the connection using a wrench if necessary, but avoid over tightening this (or any) plumbing fixture. Making certain that the appropriate washer is installed in the neck of the fixed showerhead, attach the head to one neck of the diverter and tighten it down. With the showerhead installed, apply Teflon tape to the other neck of the diverter (pictured). Attach the hose-extender attachment – with the hand-held shower attachment – to the free neck of the diverter. An attachment that fastens to the shower stem holds the hand-held attachment when it's not in use, and allows it to be positioned as a secondary fixed head.Flexible, hand-held shower head 1/4 cup of white vinegar If you enjoy taking a relaxing, hot shower and would like to replace your fixed shower head with a European type hand-held shower head, you will find that installing one of these shower heads can be surprisingly simple.

Using a hand-held shower head will allow you greater flexibility is applying shower water and will also allow you to use the sprayer to clean your shower and tub. White Bedroom Furniture AssembledYou can install one of these shower heads in less than an hour using the suggested 6 steps below.Wholesale Evening Prom Dress The old shower head will be screwed onto the water pipe that comes out of the wall. Wooden Toilet Paper Holder Free StandingBehind the shower head, towards the wall, you will find the attachment that you will need to turn in order to remove the shower head. Fit your wrench jaws over the flat part of this attachment and turn it counter clockwise until the head comes loose from the water To make it easier to screw on the new shower head, pour some vinegar into a spray bottle, then spray the water pipe threads with vinegar and allow it to sit for 5 minutes.

Then, use steel wool to clean residue from these threads and wipe them dry with a paper towel or a dry, absorbent Wrap the pipe threads with a single layer of Teflon tape, using a clockwise motion that will keep the hose attachment from unwrapping the tape when the hose is screwed onto the pipe Carefully screw onto the pipe threads the new hose attachment. Be careful that theTeflon tape is not loosened or bunched by the turning of the attachment. Screw on the attachment with your fingers, tightening it as much as possible. Then, use the wrench to finish tightening. Holding the wall mount against the shower wall in the location you prefer, turn the bracket until it is in the position you desire once the shower head is in-place in the wall mount bracket. A location about 6 inches from the old shower head should work for most people. When you have the bracket positioned, apply water resistant glue to the rear surface of the bracket. Place the surface against, the wall in the position you have chosen, then press the bracket against the wall and secure it by applying duct tape to the bracket and wall.

Give the glue a full 24 hours to dry. When the glue has set, remove the tape, place the shower head in its position in the wall bracket, and adjust its position so that the water will spray in the right direction when it's turned on. When you are ready to hold the shower head, just unsnap it from the wall bracket.This startup has re-engineered the showerhead to be radically efficient in conserving both water and heat, without sacrificing comfort.Quite a few years ago, when I was deep in my Buckminster Fuller fanboy phase (OK, so I'm still kind of in that phase), we were living in a tiny house, hauling all of our own water and using a Humanure composting toilet. I was feeling really proud that we could use a single 5-gallon solar shower to get all three of us clean, and that we could get all of our dishes and other washing done with another 5-gallon water system, but then I read about Bucky's "Fog Gun Cleaning System" (not to be confused with a fog gun-cleaning system) and realized we still had a long way to go to true water efficiency.

Fuller's design used 90% compressed air (at 200 psi), and just 10% water, in the form of atomized droplets, which he claimed would use just 1 pint of water per hour, and I remember thinking that here we are, some 50 years later, still wasting both water and heat with conventional showerheads, while this genius of an idea was relegated to a footnote in history books.Fast-forward to 2015, and a startup called Nebia has now picked up where Fuller left off (sort of), with the launch of its revolutionary showerhead, which uses a similar technology, although without the compressed air component, to deliver radical water savings in the shower. The Nebia atomizing showerhead is actually much simpler than the system Fuller designed, as it is meant to be a drop-in replacement for existing showerheads that works with existing plumbing, and while it doesn't even come close to Fuller's '1 pint per hour' claims, the Nebia is claimed to reduce shower water use by 70%, while also being 13 times more thermally efficient.

In a nutshell, the Nebia atomizes the water into tiny droplets that have "10 times more surface area" than the water drops from a conventional showerhead, allowing users to get just as clean ("more water comes into contact with your body" than with a traditional model") while also warming the air around them more efficiently. It's described as delivering a "warm and cozy mist" that not only cleans your body, but also provides a "significantly superior shower experience" overall. Here's the video pitch:The Nebia showerhead is said to use just .75 gallons per minute (gpm), which is less than the 2 gpm from EPA Water Sense-rated fixtures, and is estimated to enable an average California home of four people to use about 21,000 fewer gallons of water per year, saving about $397 per year on both water costs and water-heating costs.I love almost everything about this idea, but I have a hard time loving the price tag attached to it. Backers of the Nebia crowdfunding campaign can reserve a single unit for $299 (said to be a $399 retail value), and the company claims that the device will pay for itself in less than two years, based on the water usage in an average US home.

The Nebia is a good-looking device overall, with a height-adjustable aluminum bracket and an additional hand-held shower wand, but the showerheads themselves are essentially plastic ("a high density polymer with thermoplastic polyurethane (TPU)"), and the atomizing nozzles on the units appear to be exceptionally prone to being blocked by hard water deposits, so the $400 cost of a single unit seems way out of line to me (says the guy who has to clean the mineral scale from his shower and faucet screens every week).The Nebia showerhead does look like it could be an excellent investment for institutions and businesses that use a lot of water in their showering facilities, allowing them to conserve water while saving money on both the cost of water and the cost to heat it, and the company is offering a special deal on a bulk purchase ($10,000 for 40 units) for those situations.While you're waiting for this showerhead technology to hit the market, here's a homegrown shower hack that can save at least as much water as the Nebia, and which only costs about $20.