Your spa cover is warranted by its manufacturer, Sunstar Enterprises, 255 Redel Road, San Marcos, CA 92078, (800) 438-8677. Although basic instructions are provided below, it is important that you refer to the Sunstar information that came with the cover. Sunstar provides detailed information on caring for your spa cover and what to do to protect its warranty. WARNING: A non-secured or improperly secured cover may pose a safety threat to children and may also cause damage or injury if blown off by wind. Always remove entire cover before using the spa. IMPORTANT: Do not stand, sit, or place any item on the cover that could damage it. Gently remove any snow accumulations over 2” (5.08cm). Do not use any cleaners other than those recommended by Sunstar Entreprises. Always secure the cover with all of the cover locks when not in use, whether the spa is empty or full of water. When Super Sanitizing your spa, always follow the cover care instructions provided in the Super Sanitation section.

Cleaning the Spa Cover At least monthly, clean the spa cover following the directions below. Step 1: Remove the cover and lay it down on a flat, clean surface near a garden hose. Step 2: Rinse the cover to remove any loose debris. Step 3: Clean the top (vinyl) of the cover with a mild solution of dishwashing soap and a soft bristle brush. Using a gentle circular motion, scrub the cover, careful to not let any of the cover dry before rinsing with water. Step 4: Rinse the cover thoroughly and dry with a clean cloth. Step 5: Use saddle soap (never a petroleum-based product) to condition the cover per the manufacturer’s instructions. Step 6: Wipe and rinse any dirt from the bottom of the cover. Step 7: Replace the cover and secure the locks. NOTE: To remove tree sap, use lighter fluid (the type used in cigarette lighters). Immediately, apply saddle soap to the area. Cleaning and Protecting Spa Pillows Regularly clean all pillows with mild soap, water, and a clean cloth.

Monthly, treat pillows using a non-petroleum-based product such as 303 Protectant. This will maintain water resistance and luster of the product. IMPORTANT: Remove the pillows when shocking the spa or when sanitizer levels are high. Leave cover open for at least 30 minutes after shocking to ensure pillows are not affected. NOTE: Pillow discoloration is caused by accelerated by high sanitizer use and is not covered under the Bullfrog Spa Warranties. Low-Use or No-Use Periods During certain times of the year, you may not use the spa for a long term. For these low-use or no-use periods, consider the following guidelines: Low Use or No Use for less than Two Weeks Do not make any changes. No Use for Two to Six Weeks If the spa will not be used for at least two weeks, lower the temperature to the lowest setting of 80 F (26°C) or place in low range heat mode. Lowering the temperature will cut the cost of operation, however; you will need to adjust the temperature setting approximately 4 hours before use in order to heat the spa to 100 F (38°C).

IMPORTANT: During all low- and no-use periods, be sure to maintain the spa water as per the instructions in the Water Chemistry section. IMPORTANT: For all no-use periods, and on a weekly basis, be sure to have someone visually check that the spa is functioning correctly and to also maintain the spa water as per the instructions under the Water Chemistry section. When Does Hardwood Flooring Go On Sale At Home DepotNot doing so may lead to corrosion, staining, and/or scaling to the spa and its equipment. Solar Indoor Lights UkDuring periods of freezing temperatures, a spa that has malfunctioned may be subject to damaged plumbing or equipment as a result of ice buildup within the spa. Homes For Sale On Alligator Lake Fl

If the spa cannot be checked and maintained on a weekly basis, then consider winterizing the spa. (No use for over six weeks) When you are not planning to use the spa for six or more weeks, or when someone is not able to maintain the spa on a weekly basis, you should winterize the spa. To winterize, follow these steps: WARNING: Prior to winterizing your spa, it will be necessary to Super Sanitize the spa water as per the instructions in the Water Chemistry section. This procedure will help prevent the growth of bacteria, algae and fungi in any areas of plumbing that may not be fully free of water after you drain your spa for its period of winterization. Step 1: Drain the water.Step 1: Drain the water. NOTE: For Sport X Spas or Bullfrog Spas made before 2013 skip to Step 4 Step 2: For A or R Series spas. Open all lower valves on the JetPaks to allow the water to drain form each JetPak as you drain the spa. Once the water is completely out of the spa then close each JetPak valve before starting step 3.

Step 3: Use a wet shop vacuum to vacuum the plumbing lines by placing the vacuum nozzle over each of the lower jet faces in the spa. Lower jets are any at or below the bench seat area. Step 4: Remove the drain plug from the pump(s), loosen all PVC pipe unions, and pump air-bleed valves in the equipment compartment. Replace plugs on heater pump. Do not replace the plugs on Pump 2. Tighten the unions or close the air-bleed valves until the spa is de-winterized. Step 5: Clean the entire spa. Step 6: Remove filter cartridge(s) and clean. Do not reinstall until they are completely dry. Step 7: Secure the cover to the spa utilizing the tie downs and locking system. In areas where heavy snow is anticipated, place a large piece of plywood (or its equivalent) on top of the spa cover to assist in supporting the cover with the added weight of the snow. Remove snow off the cover following each snow storm. WARNING: To avoid water from becoming trapped between the floor suction fitting and the filter pipe .