Edit ArticleHow to Replace Spa Jets Two Methods:Bathtub SpasOutside and/or In-Ground SpasCommunity Q&A A home spa can be a wonderful and relaxing experience, especially for those who suffer from everyday aches and pains, and also to aid in the recovery of many types of injuries. Whether your spa is part of your bathtub or you have an outside spa, you may have to perform some maintenance on it from time to time, such as replacing the spa jets. Depending on the type of jets you have and where your system is located, this can be an easy procedure with just a few standard tools. Locate your owner's manual. Drain the water from your spa. Locate your spa jets. Grab your spa jets with an adjustable wrench. Tighten the wrench on your jet to get a good grip but be careful not to tighten too much to avoid damaging your jet. Turn the wrench counterclockwise (to the left) to loosen your jet. Pull your spa jets straight out from the tub. Keep your spa jets, if not damaged, so that you can reinstall them into your bathtub if desired.

To reinstall your bathtub jets, simply reverse the steps taken to remove them by seating them in the spa holes using your adjustable wrench and turning clockwise until snug. Turn on your water to test that the reinstalled jets work properly. Find the access panels for your spa (if applicable). Pry open the access panels with a flat-head screwdriver or paint spatula.Victorian Steampunk Wedding Dresses For Sale Locate the hoses and disconnect the ones that are attached to the jet you want to replace.Fly Fishing Spots Nc Remove the inside retaining ring from the old jet.Appliance Repair Leads Remove the jet collar and the rest of the assembly. Install a new gasket to replace the one removed on either the inside or outside wall of your spa (if on the outside, ensure that the surface is smooth for a good seal).

Apply some silicone to the grooves in the wall fitting. Insert the fitting into your spa-jet hole. Tighten the fitting into the jet and gasket (you need only to "hand tighten"). Reconnect the hoses to the outside of the assembly. Let the water run for about 15 minutes to clear out any debris. Place the adjustment handle for your jet into the wall fitting with the ribs aligned. Press firmly and secure the handle by snapping the clips into place. Insert the jet eyeball and cage into the handle and snap into place. Follow the manufacturer's instructions on the particular spa jet that you purchased for installing the rest of the various parts in the correct order. Run the water again to clear any debris and check for leaks, the correct jet pressure and to ensure the handle works properly. Be sure to take the necessary safety precautions when working around water and electricity and wear protective clothing such as safety glasses and gloves to avoid injury from sharp pieces of debris from your spa that may chip off when removing the old parts.

If removing and replacing the entire jet assembly, be careful to not damage the inside of the spa surface when removing the collar. This would then require resurfacing the inside of your spa.Sorry, the page you are looking for had an unexpected error on PoolSupplyWorld Find what you're looking for: Enter a name or a keyword into the search field below. Use the site navigation menu. Contact our friendly and knowledgeable staff by phone or live chat. Useful links to PoolSupplyWorld featured categories: Hot tubs are truly wonderful when they are working properly. There is nothing quite like feeling those jets churn that warm water as you sit back and relax after a hard day at work. Of course, if your hot tub isn’t working properly, it can be quite frustrating, especially if you are not at expert at hot tub repair. One of the most common problems you will experience at one time or another is a problem with your hot tub jets. Whether you are an expert plumber or don’t know which way to hold a wrench, it is still possible for you to troubleshoot hot tub jets yourself before you call in a potentially expensive repair expert.

Today, we will take a look at some of the most common problems with your hot tub jets and what you can do to repair them. It is important to note before you begin any type of hot tub repair make sure that you disconnect any power running to your hot tub. Your jets use electricity to run but as you know water and electricity don’t mix all that well. So if you don’t want to get the shock of your life, cut the power before you begin to troubleshoot any problem you may be having. Let’s take a look at some of the most common problems you will encounter with your jets and what you need to do to repair them so you can begin to use your hot tub again. One of the most common problems people experience with hot tubs is the mobile jets become fixed. This is most often caused by hard water. When your water is hard, it means that there is an excess of calcium present in the water. Over time, this calcium will buildup on the jets and even in your plumbing. Once enough calcium has built up, it can freeze the jets in place and even begin to reduce the water flow through your plumbing.

In order to repair this problem, you will first need to test your water to see if it is too hard. If it is, you can try draining your hot tub and refilling it. Once you have refilled it, test the water again to see if it is hard. If it still is hard, the only solution available is to install a water softener on your hot tub. Aqua Chek Aqua Chek Trutest Digital Reader If you find that your jets have no pressure, it is possible that air has gotten into your system. This often happens after you drain your hot tub and then refill it. Air gets trapped inside your pump and causes it to lock by preventing it from gaining any traction on the water to move it through your hot tub’s system. To get rid of this excess air, you will have to bleed it from your pump. On your hot tub you will find a discharge pipe. To bleed the air from the system you will need to loosen the coupling on the pipe. Only loosen the coupling, do not remove it. If you remove it, you may not get it back on due to the pressure from the pump.

Turn the pump on and listen for the air to be expelled. Normally you will hear a hissing sound. Once the air has been removed you should see a column of water coming from the system. Tighten the coupling and you are ready to use your hot tub. Ahh-Some Hot Tub/Jetted Bath Plumbing & Jet Cleaner (2 oz) In some cases your hot tub jets will fail to pump properly. When this happens you will often notice that they pulsate instead of provide a steady flow of water. When you experience this lack of water flow, there could be several possible solutions to the problem. The first thing you should check is the water level of your hot tub. Make sure it is filled according to the factory specs of your hot tub. If the level is too low, air could be finding its way into your system causing the jets to pulsate. If your water level isn’t too low, it could be time to check your filter. If your filter has become too dirty or clogged the water will not be able to flow through the system properly.

Remove your filter and clean it or even replace it if is worn out. Replace the filter and turn your system back on and check the flow. If it is not the filter or the water level, you could have a more serious problem. It is possible that you have a blockage in the lines of your hot tub. Check the lines to see if you can locate a blockage. If no blockage can be found, chances are the pump on your hot tub is shot and will need to be replaced. If you have gone through this guide and tried to figure out the problem with your hot tub jets but you are still unsure, don’t be afraid to call in the big guns. There are many service technicians that you can find at your local pool and spa store that can help you diagnose the problem if you are having trouble figuring it out on your own. Remember, don’t go in there blind. Hot tubs are expensive and if you are not confident in what you are doing you could make things even worse. The goal is to get your hot tub repaired so you can start enjoying it again.