Canadian Ground Shipments - Click Here for Details - Ships from Michigan Do to recent credit card fraud we can only ship to the credit card billing addressIf your bathroom fan is dead, here's some good news: You don't have to tear out the entire unit. Even if you fan is decades old, chances are you can get a replacement motor. Although a new motor costs about the same as a new fan, replacement saves time and trouble. You don't have to cut into the ceiling, crawl around your attic or get up on your roof. It usually takes less than an hour. Your first step is to get the fan's model number. Remove the fan grille (Photo 1) and vacuum away the dust to find the number on a label or stamped on the fan’s housing. But don't order a new motor until you remove the old one. You might need other parts too. Bath fans vary in design, but motor replacement requires the same basic steps, no matter which brand or model you have. Turn off the power to the fan at the main breaker panel. Then unplug the fan and remove the motor plate (Photo 2).

Some motor plates release by pressing or prying on the side of the fan housing. Others are secured with a screw or two. Before you can remove the motor from the plate, you have to get the blower off the motor's shaft. White Fluffy Cats For SaleThis is often the toughest part of the whole project. Does Grinding Help You Lose WeightAn older metal blower might be fastened with a screw. Wedding Dresses In 1977Plastic blowers usually aren't fastened at all, but simply slide off the shaft. Either way, removal may require some hard prying and pulling. If you wreck the blower while removing it, don't worry. You can order a replacement at little cost. To install the new motor, simply reverse the removal process. Replacement Motor Wheel - 50 CFM for 696N

Condensation Fan Switch with Countdown Timer in White (120-Volt, 50/60Hz) WhisperControl 4-Function Fan Control Switch 70 CFM Replacement Motor Wheel for 695 A 2-Function Rocker Combination Switch in White (120-Volt, 15-AMP(X2)) 3-Function Rocker Combination Switch in White (120-Volt, 15-AMP) QT Series Single Slide Mounting Kit Replacement Lens for 665RP Bath Exhaust Fan with Light WhisperControl 3-Function On/Off Switch with Humidity Control and Timer in White 505/509/509S Series Exhaust Fan 9.5 in. Round Aluminum Replacement Filter WhisperControl 1-Function On/Off Switch in White 807C/821C/822C/831C Series Exhaust Fan 8 in. Light Lens Replacement for 665RP, 668RP Programmable Bath Fan Control Grandera 1-Hole Wall Mount Hand Shower Holder in StarLight Chrome Wax Cartridge for 34474/542Wall Mount Shower Arm in StarLight Chrome WhisperGreen Select 3-3/4 in. x 1-2/3 in. WhisperControl 3-Function On/Off Switch with Humidity Control and Timer in Almond

NPT Threads 1-Hole Wall Mount Wall Union in StarLight ChromeIf your bathroom vent fan is making a vibrating noise, stops running or doesn’t turn on, it may be time to replace it. Most of the time the small exhaust fan motor will go bad and need to be replaced. The vent fan in your bathroom works very hard as it has to deal with heavy moisture, cold, heat, chemicals in the air, and dust. These conditions can make the fan blade impeller motor freeze up or short out. Most bathroom venting exhaust fans will last many years depending on moisture conditions. Usually these exhaust vents are installed in the bathroom ceiling and are easy to remove and replace.How to replace a noisy or broken bathroom vent fanIf your bathroom exhaust fan is making a weird vibrating noise or just will not turn on and vent out the moisture, then here is how to fix it. When performing bathroom vent fan replacement installation, you do not need to remove the complete vent assembly. You only need to remove the fan motor housing assembly.

You can then look online or take the fan housing assembly to your local home improvement store (Lowe’s, Home Depot, ACE) and match it up with a replacement fan motor assembly. These fan replacement motors are inexpensive at about $20 dollars each. They are super easy to replace, you just have to make sure you match it up with the correct replacement motor that will fit in your vent housing assembly.Use eye protection when removing and replacing the fan motor as dust will be covering everything inside the vent and may fall into your eyes.NOTE: Before replacing the fan motor, make sure the plastic cover is tight and not creating the vibrating noise because it is loose. Also, there may be a weird noise coming from inside the vent because there is so much dust and dirt covering the moving parts. At this point you can simply clean the dust off of the fan blades and surrounding area. Clean everything out using a wand style vacuum cleaner and then test to see if the noise has stopped. You can also remove the fan motor assembly (see below for how to remove) and plug the fan motor into another power outlet in the house.

This is to see if it is turning properly. You can also add a few drops of oil on the fan motor shaft if it has seized up. Once you have done everything you possibly can without replacing anything, put everything back together and test to see if it is working properly. If so, it was only dirty and replacing the fan motor is not necessary. If it still does not work properly, then follow the instructions below to replace it.Turn off the switch so power is not going to the exhaust fan. (You may need a flashlight if the vent fan and bathroom lights are on the same switch).Remove the plastic cover by unscrewing one plastic screw OR pull the cover down and squeeze the metal clips and pull downward.Unplug the fan motor power plug from the vent housing assembly.Remove or loosen the screws holding the fan motor assembly to the vent housing assembly. NOTE: Some fan motor assemblies may have to be removed differently such as with clips, slats or other.Turn the motor housing clockwise and pull downward to remove the complete fan motor assembly.